Sonoff POW Origin 16A stuck in a boot loop.

[Phillsky]

Hi again.

I figured it out.

It wont boot up connected via USB. It booted up just fine when connected to lines in, 230 volt in mycase.

Hi.

I am trying to flash a Sonoff POW Origin 16A, but its stuck in a boot loop.

this is what i see n the logs.

[I][logger:262]: Log initialized
[C][status_led:014]: Setting up Status LED...
[C][ota:469]: There have been 9 suspected unsuccessful boot attempts.
[D][esp32.preferences:114]: Saving 1 preferences to flash...
[D][esp32.preferences:143]: Saving 1 preferences to flash: 0 cached, 1 written, 0 failed
[I][app:029]: Running through setup()...
[C][uart.arduino_esp32:077]: Setting up UART...
[D][ledc.output:055]: Calculating resolution bit-depth for frequency 1000.000000
[D][ledc.output:060]: Resolution calculated as 16
[C][status_led:055]: Setting up Status LED...
[C][switch.gpio:011]: Setting up GPIO Switch 'workshop-heater - Relay Switch'...
[D][switch:016]: 'workshop-heater - Relay Switch' Turning OFF.
[D][switch:055]: 'workshop-heater - Relay Switch': Sending state OFF
[D][switch:016]: 'workshop-heater - Relay Switch' Turning OFF.
[D][binary_sensor:034]: 'workshop-heater - Button': Sending initial state OFF
[C][light:035]: Setting up light 'switch_led'...
[D][light:036]: 'switch_led' Setting:
[D][light:041]: Color mode:
[D][light:085]: Transition length: 1.0s
[C][light:035]: Setting up light 'wifi_status_led'...
[D][status_led:038]: 'wifi_status_led': Setting initial state
[D][status_led:049]: 'wifi_status_led': Setting state OFF
[D][light:036]: 'wifi_status_led' Setting:
[D][light:041]: Color mode:
[C][wifi:038]: Setting up WiFi...
[C][wifi:048]: Starting WiFi...
[C][wifi:049]: Local MAC: C0:49:EF:EF:D3:BC
ets Jul 29 2019 12:21:46

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13132
load:0x40080400,len:3036
entry 0x400805e4
[I][logger:262]: Log initialized
[C][status_led:014]: Setting up Status LED...
[C][ota:469]: There have been 10 suspected unsuccessful boot attempts.
[D][esp32.preferences:114]: Saving 1 preferences to flash...
[D][esp32.preferences:143]: Saving 1 preferences to flash: 0 cached, 1 written, 0 failed
[E][ota:476]: Boot loop detected. Proceeding to safe mode.
[I][app:029]: Running through setup()...
[C][wifi:038]: Setting up WiFi...
[C][wifi:048]: Starting WiFi...
[C][wifi:049]: Local MAC: C0:49:EF:EF:D3:BC
ets Jul 29 2019 12:21:46

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13132
load:0x40080400,len:3036
entry 0x400805e4
ets Jul 29 2019 12:21:46

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13132
load:0x40080400,len:3036
entry 0x400805e4
ets Jul 29 2019 12:21:46

Any one out there that might know whats wrong?

[ssieb]

That's a problem with the power supply.